Plastic and textile accessories for export to the EU: what to ask about REACH compliance, and what documents to request

Plastic buttons, snap fasteners, and hook-and-loop fasteners on bags and garments exported to the EU are often asked about by buyers as one of the compliance matters: chemical-level SVHC notification. This article breaks down the basic logic of this obligation by component and material, and organizes the matters and documents that should be confirmed in writing with suppliers during an inquiry.

Four-hole and two-hole plastic buttons
Four-hole and two-hole plastic buttons

SVHC notification obligation: what the 0.1% line means

A common chemical requirement under REACH for "articles"-type accessories falls on the Candidate List of Substances of Very High Concern (SVHC). Under Article 33 of REACH, if a product contains a substance listed on the Candidate List at a concentration above 0.1% (w/w), the supplier must at least inform the customer of the name of that substance. This obligation targets the candidate substances actually contained in the component, not the name on a particular certificate.

There is another point worth buyers understanding: a substance being added to the Candidate List does not mean it is immediately banned or must be replaced; listing means it may subsequently enter the authorization procedure. Therefore, a supplier's SVHC declaration is essentially a written answer to the fact of "whether it exceeds 0.1%", and it should be checked as an information obligation rather than treated as a pass to release goods.

What documents are needed: An SVHC declaration must be checked for its version and scope of coverage

You may require the supplier to provide an SVHC declaration or REACH compliance declaration corresponding to the latest candidate list version, and to state the declaration date and the scope of products or materials covered. The candidate list is continuously updated, and a declaration is valid only within the list version and date it states; some suppliers specify in the declaration that the old declaration automatically becomes invalid once a new version is published, subject to the terms of the declaration itself, and purchasers should periodically verify whether it is still the latest.

When reviewing a declaration, focus on checking three points: the update date of the candidate list on which it is based, the specific product scope to which it applies, and the way "whether it exceeds 0.1%" is stated. A declaration that only states "REACH compliant" without noting the list version and scope of coverage provides limited information; it is advisable to ask the supplier to supplement it, or at least to confirm in writing the corresponding list version.

Document checklist: Articles and preparations should be requested separately

For article-type accessories (buttons, snap fasteners, hook-and-loop fasteners, etc.), the focus is on three types of documents: material composition information, SVHC declarations, and, where necessary, test reports for specific components. If the same order also includes preparations such as adhesives and treating agents, safety data sheets (SDS) may be requested separately; an SDS provides information on the safe use of a substance or mixture, but it cannot replace the SVHC communication for article-type accessories.

Boundary statement

This article only discusses the general knowledge of the SVHC communication obligation under REACH and of RFQ documents; it does not cover the threshold determination or test methods for specific substances, nor does it draw conclusions about the actual compliance status of any supplier. Whether a specific product is compliant and which tests are required depend on the actual material combination, the version of the candidate list and the buyer's contract requirements, and should be based on the supplier's written declaration and the test reports confirmed by both parties.

Frequently Asked Questions

How to break down inquiries by component and material

The direct approach is to break an accessory down into plastic parts, metal parts, textile tape surfaces and adhesive backing and ask about each separately, rather than only asking "does this buckle comply with REACH". Taking a plastic button as an example, you can confirm whether the main body material is POM, PP, ABS or resin, and whether the surface has treatments such as spraying, electroplating or hot stamping; different parts correspond to different scopes of chemical information.

The structure of a snap fastener is more complex: in addition to the plastic shell parts, it usually comes with metal spring parts, and the metal parts can be made of copper, stainless steel or zinc alloy with electroplating treatment. When requesting a quote, you should ask the supplier to list the plastic parts, metal parts and electroplating layers separately, and to state whether each part contains substances on the candidate list and whether they exceed 0.1%. Once broken down, it becomes clear which part requires an additional declaration or testing.

Textile hook-and-loop fasteners must likewise be broken down: the tape surface may be made of different base materials such as nylon or polyester, the hook surface and the loop surface have different structures, and different types of adhesive backing and flame-retardant treatments are optional. Different base materials and adhesive backings correspond to different chemical information, so the supplier should be asked to confirm item by item according to the combination actually supplied, rather than summing it up with a single phrase "textiles are compliant".

Plastic raw materials cannot be judged by the word "plastic" alone

No. Polymers themselves generally do not directly bear REACH registration obligations, but the monomers, additives and other components in polymers are substances regulated under REACH. So seeing "this is plastic" is not enough to determine compliance status; what needs to be asked is the composition information at the raw material end and the supplier's SVHC declaration.

For buyers, a workable approach is: request from the accessory supplier the SVHC declaration issued by its plastic raw material supplier, confirm that the declaration covers the material grades actually used, and ensure it corresponds with the declaration for the finished accessory. If the supplier can only give a vague answer at the finished product level, they can be asked to explain the raw material source and the basis for the declaration; the specific test items and judgment criteria shall be subject to the test report confirmed by both parties.

Compliance declarations for textile accessories and other labels are two different things

They are two different sets of requirements and cannot substitute for each other. For textile accessories such as hook-and-loop fasteners, the supplier can be asked to confirm REACH compliance in writing; if the end market also requires textile labels such as Oeko-Tex, this should be confirmed separately and the corresponding certificates requested. The REACH SVHC notification obligation differs in scope from the certification scope of these voluntary or industry labels, and one cannot be covered by the other.

Scroll to Top